1、产品介绍Product introduction
Two-component modified epoxy resin grouting material for high solid content, high penetration, room temperature hardening epoxy reinforcement repair. Suitable for crack repair, low heat when hardening, strong and tough structure, good shrinkage, excellent adhesion and anti-cracking of various structures.
双组分改性环氧树脂灌浆料为高固含量,高渗透力,常温硬化型环氧加固修补剂。适用于裂缝修补,硬化时低热量、结构坚固韧性好、收缩性好、对各种结构物具有极佳的粘接力和抗开裂性。
2、产品特点Product features
◇High strength, strong adhesive relay, small shrinkage, stable chemical performance.
强度高、粘接力强、收缩率极小、化学性能稳定。
◇Low viscosity, good perfusion performance, also has excellent perfusion performance for small crack.
粘度低,灌注性能好,对微小的细裂缝也有优异的灌注性能。
◇According to the site construction temperature adjustment ratio, flexible construction
可根据现场施工温度调节配比,施工灵活。
◇This product has the function of reinforcing, reinforcing, plugging, waterproof, anticorrosive and so on at the same time.
该产品同时具有补强、加固、堵漏、防水、防腐等功能,使用范围广。
3、适用范围Scope of application
◇Reinforcement, reinforcement and leakage prevention of tunnels, subways and other underground structures.
隧道、地铁及其他地下建筑的加固、补强、防漏。
◇The beam, column, pile of honeycomb, cracks and other defects of the reinforcement, reinforcement, plugging leakage.
建筑物的梁、柱、桩的蜂窝、裂缝等缺陷的加固、补强、堵漏。
◇Strengthening, waterproofing and seepage prevention of dykes, ports, wharves, swimming pools and water towers.
堤坝、港口、码头、游泳池、水塔等的补强、防水、防渗。
◇Water pipeline, chemical pipeline interface seal, corrosion plugging, etc
输水管道、化工管道的接口密封、防腐堵漏等。
4、施工要点Key points of construction
◇According to different types of proportion, mix A and B evenly according to the standard ratio, and inject them into structural cracks or gaps through the high-pressure perfusion machine.
根据不同的类型配比,将A组分与B剂按标准比混合均匀,通过高压灌注机注入结构裂缝或空隙中。
◇The amount of mixing should not exceed 30 minutes of grouting amount (about 2KG is recommended). Excessive mixing amount at a single time is likely to cause polymerization reaction and accelerate curing.
每次混合的量不应超过30分钟的灌浆使用量(建议2KG左右),单次混合量过多很容易造成聚热反应,加速固化。
◇Not used up in time can material or viscosity has become very thick material, should be promptly discarded and toluene or acetone will clean the machine, so as not to block the machine.
未及时使用完的罐料或粘度已变得很稠的材料,应及时倒弃并用甲苯或丙酮将机具清洗干净,以免堵塞机具。
◇It is suggested that after the completion of the first grouting, the second grouting should be carried out at an interval of 60-90 minutes to achieve an effective repairing effect.
建议在第一灌浆结束后,间隔60-90分钟后,进行二次补强灌浆,以达到有效的修补效果。
◇After 3 days of grouting, the remaining epoxy solidified on the lining can be cleaned, the grouting needle removed, and the pinhole sealed with waterproof mortar.
灌浆完成3天后即可清理凝固在衬砌上的残余环氧,去除灌浆针头,用防水砂浆封填针孔。 |
|